|
|
05-03-2017, 08:42 AM
|
#1
|
Senior Member
Join Date: Jul 2009
Posts: 129
|
Using Drill To Level A TM
I have a 2008 2720 TM. I am thinking about leveling the TM using a drill on the leveling jacks.
Does anyone have experience using a drill to level. Does the drill have enough power to lift the trailer enough to level it up? Does anyone use a battery powered drill to level?
I would prefer to use a battery powered drill since I often go where there is no electric and a battery powered drill would be much easier in any event.
Anyones experience would be greatly appreciated.
Thank you,
Phil
__________________
TV - 2005 Toyota 4Runner, V8, Prodigy Brake Controller, EZ WDH.
TM - 2008 2720, 15" Wheels, Two 4D Lifeline AGM Batteries, Linklite Battery Monitor, Self Adjusting Brakes.
|
|
|
05-03-2017, 08:49 AM
|
#2
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,115
|
Many of us use an 18-volt drill to lower the jacks to ground level, and to raise them when breaking camp. It is quick and easy. But unless you have a moose of a drill, it won't lift the TM. At least mine won't.
Bill
|
|
|
05-03-2017, 08:59 AM
|
#3
|
TrailManor Master
Join Date: Sep 2010
Location: Jo-juh
Posts: 420
|
Assure that the screws are lubricated, and yes it will run them up/down but doubtful it will have enough torque to lift the trailer.
__________________
Mark
'20 Ford F250 Lariat 6.7 L 4WD (Herschel)
'22 Keystone Cougar 32BHS 5er (Mellencamper)
'01 Ford Excursion Limited 7.3 L PSD 4WD (Rudolph) (Sold)
'18 Keystone Cougar 29BHS (Sold)
'15 Prime Tracer 25BHS (Traded)
'06 TrailManor 2619 (Traded)
:cwmddd:
|
|
|
05-03-2017, 09:03 AM
|
#4
|
Site Sponsor
Join Date: Mar 2015
Location: Everett, WA
Posts: 213
|
Craftsman Impact wrench
I have a Craftsman impact wrench like this one:
https://www.craftsman.com/products/c...red-by-4ah-xcp
It does lift the trailer for leveling (and makes quite the racket while doing the heavy lifting). My battery is about half the size of the one pictured and I usually don't get 2 lifts without recharging. (So I can go down, then up, then down again, but not enough power to lift it back up)
This is the battery I have:
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
__________________
TM: 2007 2720 (QB) TV: 2010 Toyota Highlander Hybrid
Hopkins INSIGHT brake controller, Andersen No-Sway WDH
CARCHET Solar Powered TMPS
Dometic CRX-1110 AC/DC Compressor Fridge, 200 W Solar
|
|
|
05-03-2017, 09:17 AM
|
#5
|
TrailManor Master
Join Date: Nov 2016
Location: Vancouver BC
Posts: 1,521
|
So far, I've found it pretty easy to level by using a 1' level to estimate how many 5/8 pieces of plywood I need under a wheel to level side to side. Then I use the tongue jack to level end to end. I've been pretty good about estimating the plywood pieces so far. A 1/8" gap would mean I'd 2 boards under the low side, done just before unhitching the TV.
|
|
|
05-03-2017, 01:00 PM
|
#6
|
TrailManor Master
Join Date: Jan 2014
Posts: 893
|
Ryobi is the only brand I know of that sells a 12V charger for their batteries. This is convenient if you want to charge from the car or solar while boondocking. So I use their drill, vacuum, and air pump.
|
|
|
05-19-2017, 09:49 AM
|
#7
|
Senior Member
Join Date: May 2017
Posts: 57
|
|
|
|
05-15-2018, 11:19 AM
|
#8
|
Senior Member
Join Date: Dec 2010
Location: Lexington Park, MD
Posts: 151
|
Where do you place your level, on the tongue prior to opening the TM?
__________________
Steppy
2013 2720SL
2011 Honda Ridgeline TV
Tekonsha P3 Brake Controller
Curt WDH Trunnion 800 # TW
|
|
|
05-15-2018, 05:09 PM
|
#9
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,115
|
For fore-and-aft leveling, I have a 6" magnetic level with a magnetic strip on one edge, which I place on one of the triangle sides of the A-frame. Works well, and is easy to see as I crank the jack up/down.
Bill
|
|
|
05-03-2017, 02:17 PM
|
#10
|
Member
Join Date: May 2008
Location: NC
Posts: 23
|
Dewalt 18 volt drill does me fine. If your trying to raise trailer you can alway use hand drill. Using scissor jacks too much sort of makes my TM not fit together well so I get wheel and tongue as close to level as possible
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Thread Tools |
|
Display Modes |
Hybrid Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|