|
|
10-24-2024, 05:27 PM
|
#11
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,207
|
Ah, yes, the 264 RB does have a clear panel, which would be used for the backup light. That accounts for the Backup light input, and means you don't have to grub around behind the refrig.
It comes on during the running light test, as you noted above. That accounts for the Running Light input.
I'm not sure what TM did with the Stop/Turn input. Perhaps doubled it up with the running light input?
Anyway, it sounds like you are out of the woods, and everything is working acceptably.
Bill
|
|
|
10-24-2024, 05:54 PM
|
#12
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,207
|
Now that we have solved the issue, there is a way to combine the two Stop/turn lights (coming from the tow vehicle) into a single wire that can be connected to the single Optronics Stop/turn input. Get a couple cheap silicon diodes such as 1N4001 or (better) 1N4002. Less than $1 for the pair. Twist the leads on the striped ends together, adding the end of a 1-foot length of hookup wire to the twist. Solder the three of them together. Then connect (meaning twist and solder) the TM's Left turn/stop wire to one of the unused diode ends. Connect the TM's Right turn/stop wire to the other diode end. Insulate all three joints. Done.
The only remaining challenge is figuring out where to put this assemblage. The diodes are small, and the whole thing can be inserted into a length of heat shrink tubing. With care, the end result will be a tube less than 2" long and 1/8" diameter. Bring out the free end of the hookup wire and connect it to the Optronics Stop/turn input wire.
BTW, I'm a fan of soldering if you know how to do it correctly. But connections don't have to be done that way. When I say "solder" I really mean "make a reliable connection". You could make the connection with small wire nuts, crimp connectors, or other mechanical fasteners. Not my choice, but if done carefully, they work.
Bill
|
|
|
10-25-2024, 04:39 AM
|
#13
|
TrailManor Master
Join Date: Aug 2015
Location: Rochester, NY
Posts: 1,900
|
How do the diodes (electricity one way check valve) stop the blinking, which is achieved by applying and removing voltage from the circuit?
__________________
2007/21 TM 3326 (Pride of the Fleet)
2000 2720SL (Rebuild Project)
2002 2619 (Parts TM)
SMARTER THAN GOOGLE!
|
|
|
10-25-2024, 08:25 AM
|
#14
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,207
|
They don't stop the blinking, and I'm not sure you would want them to.
If you turn on the blinker in either direction, without pressing the brake pedal, the Optronics light (in the high center position) will flash in sync with the regular blinker (mid-height on the chosen side). I see no problem here -- it serves as an alert to the following driver, especially valuable in merging traffic where the side light might not be visible.
If you press the brake pedal without turning on a blinker, the Optronics in its high center position will come on steady. Many SUVs do this.
If you do brake pedal and blinker at the same time, the Optronics will come on steady, again like many SUVs.
This is a very simple device, but IMO, the result would be a good thing. Again IMO, TM would do well to integrate this into the trailer build. Cheap and easy - and a good FEATURE to add to the list on their web site.
Bill
|
|
|
10-25-2024, 10:33 AM
|
#15
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,207
|
It occurs to me that the entire diode package, in the heat-shrunk tube, is small enough that it could be mounted on top of the Optronics device, against the TM wall, and buried in a line of caulk. Can't get much simpler than that.
Bill
|
|
|
|
|
Currently Active Users Viewing This Thread: 6 (0 members and 6 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|