|
06-28-2017, 01:17 PM
|
#1
|
TrailManor Master
Join Date: Nov 2016
Location: Vancouver BC
Posts: 1,530
|
Torsion bars
This is a little bit of a crazy question, but here goes...
Has anyone every had replacement torsion bars made up locally? I know I could get them from TM, but if torsion bars in general use the same type of steel, that means that the spring (or torsion) constant would be determined mainly by the length and diameter of the bar.
I'm hoping to save on shipping costs if something can be found locally.
|
|
|
07-01-2017, 07:17 PM
|
#2
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,179
|
Larry -
TM uses, and stocks, at least a couple dozen different torsion bars. Recently someone posted a link to a series of photos of a TM factory tour. One of the photos showed a big rack of different torsion bars. Check it out!
Bill
|
|
|
07-01-2017, 07:28 PM
|
#3
|
TrailManor Master
Join Date: Nov 2016
Location: Vancouver BC
Posts: 1,530
|
Bill,
I do realize I can get them from TM. I was curious if I could save on shipping, and also the exchange rate. I'm guessing it's not worth chancing.
|
|
|
07-02-2017, 06:41 AM
|
#4
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,179
|
Larry -
I understand, and I missed that point about your query. My bad.
Not being a metallurgist, I don't know how to make a torsion bar, but I'm thinking the steel is probably special in some way, so that it twists and rebounds, rather than twisting and taking a set. After all, the bar twists 90 degrees over an 8-foot length, and is expected to do this hundreds of times.
My immediate thought is that you have to tell the fabricator what you need, and I have no idea how to specify the performance (the strength, mainly). The fabricator is unlikely to give you a refund if you give him the wrong performance numbers.
Perhaps some of the scientists here on the board could offer suggestions.
Bill
|
|
|
07-02-2017, 07:52 PM
|
#5
|
TrailManor Master
Join Date: Jan 2014
Posts: 893
|
The Wikipedia article on spring steel lists several alloys. The heat treatment required is annealing during shaping, then hardening, then heating to about the Curie point for tempering. Sounds like a job for a specialist. You would not achieve your desired torsion on the first try. The specialists have a repeatable process.
|
|
|
07-02-2017, 08:02 PM
|
#6
|
TrailManor Master
Join Date: Nov 2016
Location: Vancouver BC
Posts: 1,530
|
Quote:
Originally Posted by BrucePerens
The Wikipedia article on spring steel lists several alloys. The heat treatment required is annealing during shaping, then hardening, then heating to about the Curie point for tempering. Sounds like a job for a specialist.
|
If I were to consider this route, I'd only go with a company that actually makes torsion bars. I'm not even sure if there's anyone local here that does that in the first place. I imagine TM has their torsion bars made for them.
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|