|
|
01-05-2010, 07:01 PM
|
#11
|
TrailManor Master
Join Date: Aug 2009
Location: Colorado
Posts: 605
|
Thanks. We have been laughing all day that we are obviously not cabinet makers. The pictures are making us look better than we are but we think the drawers are going to do the job.
Malinda
__________________
'06 2619
Gene & Malinda, Delilah & Koko
'12 Toyota Tundra 4.6 V8 Tow package - Leer XL
Thule for our tandem Hobie Kayak :-)
120w Solar Panel - 2.5" lift 15" Marathons
[SIGPIC][/SIGPIC]
|
|
|
01-07-2010, 04:05 PM
|
#12
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,176
|
Nice work, guys! And again, thanks to Rick Newcomb for hosting the instructions on his site for years!
Bill
|
|
|
01-08-2010, 07:19 AM
|
#13
|
Guest
|
When I made my 3 drawers two years ago, I accidentally made them a bit too tall. But all I had to do was set the fence on my table saw and whack it off. This resulted in a very even top surface.
If I ever build a drawer again, I will do the same. Trying to get the top and bottom edges to both be even is not easy.
|
|
|
03-31-2010, 09:38 AM
|
#14
|
Guest
|
Slide-out Kitchen drawers
Hi Bill,
I'm looking at your kitchen drawers and just drooling. We're going on a 7 week trip (DH's sabbatical, yea!) and I just need to be organized.
Quick question, did you drill the rear slide supports directly into the side of the TM? I've been worried about drilling holes because of leakage, etc. Is this an issue?
Thank you!
Trish
|
|
|
03-31-2010, 10:58 AM
|
#15
|
Guest
|
Malinda -- your shelves are beautiful too!
Quick question, if you make modifications liek this does it void your warranty? Hubby is worried about doing too much to the trailer.
thank you!
|
|
|
03-31-2010, 12:03 PM
|
#16
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,176
|
In my case, the back end of the rail is supported by a rail holder, which is screwed to the wall. Putting a hole in the inner skin of the wall won't cause any leaks. The wall is quite thick, so your sheet metal screw should protrude from the back of the rail holder by about half an inch. Just be sure you don't make the screw so long that it pierces the outer skin of the TM.
No, there should be no warranty implications as long as you don't penetrate the outer skin. Of course, if you do make a hole all the way through, and the hole leaks, that's another story.
Bill
|
|
|
03-31-2010, 03:18 PM
|
#17
|
TrailManor Master
Join Date: Aug 2009
Location: Colorado
Posts: 605
|
Thanks Trish. They were SO worth the work and cost. I'd just add, if you stain the drawers, let them dry really, really well before you put them in. We did ours in January so it was pull it out on a nice day and make it happen. Wow, stinkfest! We left the TM semi-open in the garage with the cabinet doors open for a few days afterward. That was not anywhere near good enough.
The modification for the existing drawers is looming large on my radar.
Malinda
__________________
'06 2619
Gene & Malinda, Delilah & Koko
'12 Toyota Tundra 4.6 V8 Tow package - Leer XL
Thule for our tandem Hobie Kayak :-)
120w Solar Panel - 2.5" lift 15" Marathons
[SIGPIC][/SIGPIC]
|
|
|
04-24-2010, 08:16 AM
|
#18
|
Guest
|
For everyone who is not as handy as Bill and Malinda --- I found a company http://shelvesthatslide.com that sells their customer returns on eBay. Using Bill's design plan (and measuring and re-measuing), I was able to buy 5 slideouts and required hardware for $190 (lacquered, shipping / tax included). Essentially ended up being about $30 / shelf which is a deal for me because I don't have the tools or talent to do this myself. If you want to save even more $$, they have shelves that haven't been finished for around $15.
here is a link to the eBay store: http://stores.ebay.com/shelvesthatslide
My shelves haven't arrived yet, but I've got my fingers crossed thsi will work. I talked to people at the company and they're very nice. And they also have an eBay feedback rating of 100%.
Now I just need to figure out how to install them. :-) Again, many thanks to Bill and Malinda for their inspiration. You've made my OCD day! :-)
|
|
|
05-03-2010, 09:41 AM
|
#19
|
Guest
|
Quick update. I received and installed the pull-out shelves mentioned above and am thrilled with the results, quality, etc. The people at the company couldn't be nicer and the package came with everything I needed for installation. The only crazy part was installing the 22" drawer next to the sink. Felt like a contortionist -- but now it's done!
|
|
|
05-04-2010, 07:27 AM
|
#20
|
TrailManor Master
Join Date: Aug 2009
Location: Colorado
Posts: 605
|
That sounds like a steal to me! Great find! All the thanks go to Bill who opened the door!
Malinda
__________________
'06 2619
Gene & Malinda, Delilah & Koko
'12 Toyota Tundra 4.6 V8 Tow package - Leer XL
Thule for our tandem Hobie Kayak :-)
120w Solar Panel - 2.5" lift 15" Marathons
[SIGPIC][/SIGPIC]
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|