|
10-29-2007, 12:50 PM
|
#1
|
Guest
|
Recommed WDH? Double receiver for bike rack?
1) Can anyone recommend a good WDH? Just like everyone, I am looking for good quality and ease of use. I hear the Equilizer and Reese WDH mentioned a lot. Anything good or bad about both? Or any other ones recommended?
2) Also, I saw a TV with a receiver that split off into two other receivers, one receiver over another. The bottom receiver was used to tow the trailer and the top receiver had a bike rack on it. I never got the name of the manufacturer and it didn't look homemade. Anyone ever see anything like that before?
|
|
|
10-29-2007, 01:05 PM
|
#2
|
Site Sponsor
Join Date: Jul 2003
Location: MD
Posts: 412
|
dual hitch receiver at camping world
Quote:
Originally Posted by CORNFEDDOBY
2) Also, I saw a TV with a receiver that split off into two other receivers, one receiver over another. The bottom receiver was used to tow the trailer and the top receiver had a bike rack on it. I never got the name of the manufacturer and it didn't look homemade. Anyone ever see anything like that before?
|
http://www.campingworld.com/browse/s...EJbe0K9gBRMUKw
__________________
Tim
2004 2720SL TrailManor, 2 X T105, Trimetric 2030RV, TST TPMS
2003 Tundra Access V8 2X4 w/Tow Pkg
Equal-i-zer 1000, Prodigy, McKesh, UnderCover
|
|
|
10-30-2007, 05:47 PM
|
#3
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,198
|
I have never hooked up an Equal-I-Zer hitch, but I seem to recall that in order to raise the spring bars into towing position (and presumably to lower them as you unhitch), you have to jack up the tongue of the trailer while the coupler is attached to the hitch ball on the tow vehicle. Can anyone confirm or deny?
With a more conventional WDH, such as the Reese you mention, the spring bars have a short length of chain attached to the tips. You put the proper link of the chain over a hook that is on the trailer frame, and raise the hook with a "cheater bar" - a short length of pipe. No jacking is required.
Bill
|
|
|
10-30-2007, 07:36 PM
|
#4
|
TrailManor Master
Join Date: Aug 2004
Location: Ada, OH
Posts: 254
|
Quote:
Originally Posted by Bill
I have never hooked up an Equal-I-Zer hitch, but I seem to recall that in order to raise the spring bars into towing position (and presumably to lower them as you unhitch), you have to jack up the tongue of the trailer while the coupler is attached to the hitch ball on the tow vehicle. Can anyone confirm or deny?
Bill
|
Sure Bill, I'll confirm your statement. When I connect the TM to the TV I connect the hitch to the ball, then extend the electric jack to raise the hitch so I can easily push the spring arms onto the sway bracket. Then retract it and I'm ready to go...
Also when disconnecting the TV/TM I extend the jack, which releases the pressure on the spring arms so they can easily be swung out. All this is made much easier because of the electric jack.
CornFedBou, here is a link to the directions, just in case you hadn't already seen it.
http://www.equalizerhitch.com/pdf/eq...structions.pdf
HTH, Keith
__________________
Keith and Kathy
'07 Explorer 4.6 V-8 - '07 2720SL
Equal-i-zer 1000 - Prodigy - McKesh
|
|
|
10-31-2007, 03:36 PM
|
#5
|
yes, they hunt lions.
Join Date: Aug 2005
Location: Reno, NV
Posts: 1,361
|
"Robin" is a clone for Reese,
and typically costs a lot less. (Camping World, local store, wherever). For a TM, buy the "1000 lb." version.
__________________
TM='06 2619 w/5K axle, 15" Maxxis "E" tires. Plumbing protector. 800 watts solar. 600AH LiFePO4 batteries, 3500 watt inverter. CR-1110 E-F/S fridge (compressor).
TV = 2007 4runner sport, with a 36 volt "power boost".
|
|
|
11-02-2007, 01:25 PM
|
#6
|
Guest
|
Thx
Thx for your replies. Will be driving around North Florida tomorrow to look at few TM. Then will end the day Mountain Biking at Santos Trailheads in Ocala. Thx for the responses.
|
|
|
11-02-2007, 02:45 PM
|
#7
|
Guest
|
Another factor to consider with the Equalizer is, it's HEAVY. We really like ours otherwise, but be aware of what you're getting, particularly if you'll be taking it off and reinstalling often. It helps to take the spring bars off separately before removing the hitch itself. I always do this, but have seen folks taking the whole assembly off (including spring bars) at once. Ouch!
Jon and Rita
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|