|
|
03-11-2008, 11:36 AM
|
#1
|
Guest
|
Bed slides worned down
I notice when pulling the beds out (or in) the nylon running strips are pretty worned out and one has broke away and I can see the frame. Has anyone replace these strips, or is this something I should take to the dealer to have done. Looks like 1 to 1 1/2" wide and no more than 1/8" thick. Has anyone tried replacing them?
Thanks,
Joe
|
|
|
03-11-2008, 12:11 PM
|
#2
|
Guest
|
Quote:
Originally Posted by JOEALAN
I notice when pulling the beds out (or in) the nylon running strips are pretty worned out and one has broke away and I can see the frame. Has anyone replace these strips, or is this something I should take to the dealer to have done. Looks like 1 to 1 1/2" wide and no more than 1/8" thick. Has anyone tried replacing them?
Thanks,
Joe
|
I just ordered replacements from Adam at TrailManor. Looks like just a matter of unscrewing the old ones and mounting the new ones. I'll reply again if I run into anything unforeseen. Replaced the bed bolts also so hopefully good for another 10 years.
Brian
|
|
|
03-11-2008, 06:44 PM
|
#3
|
Site Sponsor
Join Date: May 2005
Posts: 57
|
nylon bed slides
I've replaced one side of my bed slides. For some reason the other side was still in perfect shape. Called Trailmanor service and they sent them right on out. No problem replacing.
__________________
2005 3124KS 2004 F-150
|
|
|
03-11-2008, 08:02 PM
|
#4
|
Site Sponsor
Join Date: Jun 2003
Location: Santa Cruz County, CA
Posts: 2,405
|
Are you talking about the slides that attach the support arms that swing in and out when you pull the bed in and out (under the bed) or the slides along the sides of the bed?
I've fixed the ones along the sides. It was a time-consuming process. Replacing the bottom "guides" should be super easy, just get a part from the TM factory.
__________________
'97 2720 & '01 Chevy Silverado 1500 4x4
2011 & 2017 Prii, 10'x18' & 10'x9' Tents
|
|
|
03-12-2008, 08:00 AM
|
#5
|
Guest
|
Bed slides
B & D I think we are talking about the same bed slides. Looks approx. 1/2 to 1 inch wide, 1/8" think and at least the lenght of bed (96" long) when siding in and out. Visible while inside trailor pulling beds out and into there stationary position when setting up.
Our they difficult to remove? Can you remove old and install new without removing bed? Our they glued or screwed on? Any information would be helpful.
Thanks everyone for your response.
Joe
|
|
|
03-12-2008, 08:02 AM
|
#6
|
Guest
|
Quote:
Originally Posted by Brian3023
I just ordered replacements from Adam at TrailManor. Looks like just a matter of unscrewing the old ones and mounting the new ones. I'll reply again if I run into anything unforeseen. Replaced the bed bolts also so hopefully good for another 10 years.
Brian
|
Thank you Brain, I believe the ones your talking about are the nylon fittings on the outside of the TM bed arms.
Again, thank you. Joe
|
|
|
03-12-2008, 08:04 AM
|
#7
|
Guest
|
Quote:
Originally Posted by 2blueranger
I've replaced one side of my bed slides. For some reason the other side was still in perfect shape. Called Trailmanor service and they sent them right on out. No problem replacing.
|
Thank you. Joe. Did you glue or fastened down?
|
|
|
03-12-2008, 11:59 AM
|
#8
|
Site Sponsor
Join Date: Jun 2003
Location: Santa Cruz County, CA
Posts: 2,405
|
When I fixed ours I had to take the bed out, remove the old broken pieces and old glue (not just the strips are glued on, my fabric was glued onto the metal support L and the plastic was glued on top of that), re-glue everything, and then put the bed back in. If you would like more details PM me and I'll fill you in. I also have a drawing that I made for another TM board member that explains the way I did it. It took me about a week, but I wasn't in a hurry. I wanted to do it once, do it right, and never have to do it again. I thought it was important to have a smooth surface along the outside (no screws) otherwise it will tear up the corner molding in the bathroom and behind the folding wardrobe.
__________________
'97 2720 & '01 Chevy Silverado 1500 4x4
2011 & 2017 Prii, 10'x18' & 10'x9' Tents
|
|
|
03-13-2008, 07:30 AM
|
#9
|
Guest
|
Quote:
Originally Posted by B_and_D
When I fixed ours I had to take the bed out, remove the old broken pieces and old glue (not just the strips are glued on, my fabric was glued onto the metal support L and the plastic was glued on top of that), re-glue everything, and then put the bed back in. If you would like more details PM me and I'll fill you in. I also have a drawing that I made for another TM board member that explains the way I did it. It took me about a week, but I wasn't in a hurry. I wanted to do it once, do it right, and never have to do it again. I thought it was important to have a smooth surface along the outside (no screws) otherwise it will tear up the corner molding in the bathroom and behind the folding wardrobe.
|
Thanks B & D. It looks like a project I'm going to hold off until the winter. I think I can at least remove the broken section out and replace for the time being.
Since I cannot park my TM outside my garage on my property (Silly city rules and regulations) I'll need to move my TM to a place where I can work on it for more than one day.
Joe
|
|
|
04-10-2009, 07:31 AM
|
#10
|
Guest
|
Sway arms, replace nylon track
Quote:
Originally Posted by Brian3023
I just ordered replacements from Adam at TrailManor. Looks like just a matter of unscrewing the old ones and mounting the new ones. I'll reply again if I run into anything unforeseen. Replaced the bed bolts also so hopefully good for another 10 years.
Brian
|
Brain, did you replace the nylon strip and bed bolts? My son thinks we need something to hold up the extended bed before you can remove and replace nylon strip otherwise it could collaspe? The last time I had it open late summer, it look like a clear cut easly removal. Anyone out there have any problems replacing?
Joe
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|