TrailManor Owner's Forum  

Go Back   TrailManor Owner's Forum > TrailManor Technical Discussions > Frame
Register FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 02-05-2006, 05:52 PM   #1
PopBeavers
Guest
 
Posts: n/a
Default Cracked Frame

Has anyone had a problem with a cracked frame?

I took deliver of a new 2005 TM 2720 in March 2005. Today, while gettigng ready for the second season, I saw a line of rust. I thought it was just a streak from rusty water, but it is a crack down the entire outside of the box tube and also along the bottom and just barely upe the inside face. Slightly more than one half of the stee has failed. The failure appears to have started at the edge of the weld that attaches the swing away hitch to the main frame.

I sure am glad I noticed it before we took it out.

How often do most owners examine the frame for cracks? What do you do about them?

I'll be on the phone Tuesday with Dinuba RV to see about some warantee work.
Attached Thumbnails
Click image for larger version

Name:	TMWeldFail.JPG
Views:	2338
Size:	56.7 KB
ID:	965  
  Reply With Quote
Old 02-05-2006, 06:04 PM   #2
Bill
Site Team
 
Bill's Avatar
 
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,225
Default

Wow! The photo says it all. Start with Dinuba, but since TM fabs their own frames at the plant in TN, my guess is that you will be referred back to the factory PRONTO.

Never heard of this problem. Please let us know how the solution progresses.

Bill
Bill is offline   Reply With Quote
Old 02-05-2006, 07:03 PM   #3
PopBeavers
Guest
 
Posts: n/a
Default

I'm real nervous about how this is going to play out. I am not willing to tow the TM in it's current state. I will not assume that level of liability. I can only guess what happens when one side of the frame completely fails while towing.

Either someone has to come to my house to fix it or someone that knows what they are doing needs to come to my house, load it onto a hauler and properly secure it for transport. I don't think it can be hauled with any weight on the swing away tongue. And I don't think the front jacks are designed to carry the weight of the TM bouncing on a hauler. There would need to be some cribbing or some other way to support the front of the frame without using the swing away tongue and without using the front jacks.
  Reply With Quote
Old 02-05-2006, 10:31 PM   #4
RockyMtnRay
TrailManor Master
 
Join Date: Jul 2001
Location: Colorado Springs, CO
Posts: 816
Default 2nd reported instance of a cracked tongue

Quote:
Originally Posted by PopBeavers
Has anyone had a problem with a cracked frame?

I took deliver of a new 2005 TM 2720 in March 2005. Today, while gettigng ready for the second season, I saw a line of rust. I thought it was just a streak from rusty water, but it is a crack down the entire outside of the box tube and also along the bottom and just barely upe the inside face. Slightly more than one half of the stee has failed. The failure appears to have started at the edge of the weld that attaches the swing away hitch to the main frame.

I sure am glad I noticed it before we took it out.

How often do most owners examine the frame for cracks? What do you do about them?

I'll be on the phone Tuesday with Dinuba RV to see about some warantee work.
To the best of my knowledge, this is actually the second reported instance of a cracked tongue...here's the thread of the other instance I suspect it's probably not coincidental that both your and Russ-Bett's cracks are in the vicinity of the hinge point for the swing tongue. Out of curiousity, do you ever swing the tongue with the weight of the trailer on it?

I check my tongue for anything unusual before each trip...and any rust would be very unusual given my dry climate. Like most folks with the swing away tongue, so far so good...no noticeable problems.
__________________
Ray

I use my TM as a base camp for hiking, kayaking, mountain biking, and climbing Colorado's 14ers


The Trailer: 2002 TM Model 2720SL ( Mods: Solar Panels (170 Watts), Dual T-105 Batteries, Electric Tongue Jack, Side AC, Programmable Thermostat, Doran TP Monitor System)

The Tow Vehicle: 2003 Toyota Tundra V8 SR5 4X4 w/Tow Package (Towing & Performance Mods: JBA Headers, Gibson Muffler, 4.30 gears, Michelin LTX M/S Tires, Prodigy Brake Controller, Transmission Temperature Gauge)


RockyMtnRay is offline   Reply With Quote
Old 02-06-2006, 08:10 PM   #5
Bill
Site Team
 
Bill's Avatar
 
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,225
Default

Quote:
Originally Posted by RockyMtnRay
Out of curiousity, do you ever swing the tongue with the weight of the trailer on it?
Ray makes a really good point here - one that I hadn't even considered. I haven't talked to the factory about it, but after some reflection it seems obvious that no weight should be put on the tongue (as, for example, with the tongue jack) when the tongue is unlatched and swung open. Not only does ALL of the tongue weight (rather than half) come down on one side of the frame. But it twists the frame member sideways, in a direction that it is not designed to resist.

I have to admit I have done this myself, without even thinking. Pull the pin on the swing tongue and swing it around to the side. Then put the bogey wheel on the jackstem, crank the jack down to take the weight off the stabilizers, and move the trailer with the entire tongue weight on this out-of-position support. BAD BAD BOY! I won't do it again.

New rule, folks! If you have a swing tongue, NO WEIGHT ON IT unless the tongue is swung closed and pinned in travelling position! I just reviewed the Owners Manual, and it doesn't seem to say anything about this. But I bet it will ...

Having said all that, I have no idea whether this was the cause of PopBeaver's failure.

Bill
__________________
2020 2720QS (aka 2720SL)
2014 Ford F-150 4WD 5.0L
Bill's Tech Stuff album
Bill is offline   Reply With Quote
Old 02-06-2006, 08:32 PM   #6
Senorsedona
Guest
 
Posts: n/a
Wink A lesson to be learned.

I agree with Bill, now that the subject comes up. I might have moved the TM with the tongue swung out of the way. It sure sounds like a real NO, NO. I'm glad this has been brought up. Even if it was not the cause of his frame cracking. We all should take it as a learning tool.

Good luck resolving the problem.

Jack
  Reply With Quote
Old 02-06-2006, 08:52 PM   #7
PopBeavers
Guest
 
Posts: n/a
Default

I have always had the front of the TM supported by the two front jacks before taking the weight off the wheel and popping the pin to swing the toungue around.

It never occurred to me to keep weight on it. Maybe some of the engineering classes I took so long ago actually sunk in.

My son is about to graduate with a degree in Mechanical Engineering. He was VERY curious.

Even though Dinuba RV is closed on Mondays, I received an email from Stan indicating that he would forward the picture to the factory. By 12:44 today I had a request from the factory, via Stan, for additional photos. So far that is better than I had hoped, seeing as I knew that Dinuba RV was closed.
  Reply With Quote
Old 02-07-2006, 07:02 AM   #8
jimwilly
Senior Member
 
Join Date: Mar 2005
Posts: 54
Default Wheel under front jack

Reading this thread about the cracked frame got me to wondering. I just traded for a previously owned 2003 TM3023. I ditched my Coleman, which we have really enjoyed. My question - Our Coleman had a wheel under the front jack that allowed me to move the camper slightly, especially when parked in the garage on concrete. My TM does not have a wheel under the jack. It never occurred to me until now. Since I am a new TM owner, having not used the TM yet, the wheel, or lack thereof, just occurred to me.

Should I have a wheel under the jack or is that not something TM uses?

Thanks for any comments. I jsut love this forum!
jimwilly is offline   Reply With Quote
Old 02-07-2006, 08:24 AM   #9
PopBeavers
Guest
 
Posts: n/a
Default

I back the TM into the garage at a slight angle. After disconnect I push the front over to the side about 2 feet to anle it the other way. Then I set the front jacks and swing the tongue around. It rolls well on a concrete floor.
  Reply With Quote
Old 02-07-2006, 08:58 AM   #10
mjlaupp
Site Sponsor
 
Join Date: May 2002
Location: Downsville, Louisiana
Posts: 1,069
Default

Yes there should be a dolly wheel for the jack. Having said that, I don't use mine most of the time.
Mike
__________________
Mike Laupp

2013 Jayco Eagle Premier 351RLTS 5er - Honda 2000i x2 w ext. run tank

2017 F350 King Ranch ultimate CCLB SRW 6.7L V8 TD Fx4 BakFlip F1 & BakBox

TM History: '97 2720, '02 2720SL, '03 2720SL, '04 3326K. 2001 - 2012 yrs owned.

1990 Isuzu Trooper II 283 V6
mjlaupp is offline   Reply With Quote
Reply

Tags
hitch alignment, hitch failure, swing hitch


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 03:31 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 2022 Trailmanor Owners Page.