|
|
03-21-2009, 04:45 PM
|
#1
|
Member
Join Date: Jan 2008
Location: Barrie, Ontario
Posts: 44
|
Newbie Towing Question
We are planning a trip to the west coast in the spring. I have never pulled the Trailmanor in the mountains. Everyone says that you should not tow in overdrive especially if the transmission is moving back and forth between gears. My question is this: Do I choose a gear when in the mountains or do I downshift when necessary. Is there a gear I should try to stay in. Thanks in advance for any replies.
__________________
Heather & Ron
2008 3124KS
2008 Toyota Highlander
Prodigy Brake Controller
|
|
|
03-21-2009, 05:29 PM
|
#2
|
Guest
|
towing in mountains
Heather & Ron
I have an older 4-runner with a 3.4 liter v8 "183 hp" and also tow a 3124KS.
Your 2008 Toyota Highlander is most likely a 3.5 V6 at 270 hp with a 5 speed trans. From what I understand, towing with the overdrive on uses a planatary gear which gears it more than 1-1 ratio. 4th gear should be a 1:1 ratio, but I may be wrong because I am not familiar with the Highlander.
I constantly go up and down 1-70 from Denver which is a 7% grade in about 3 places. I always leave my overdrive off increase my braking on the trailers electric brakes and use my engine compression downhill when I can. The brake rotors are fairly thin on the 99 4runner and they will warp fairly easy when overheating them.
Going uphill -- 6% grade 55mph, 7% grade 25-30mph.
Happy camping.
|
|
|
03-21-2009, 06:50 PM
|
#3
|
Guest
|
I tow with a Mercedes ML320- It's a big 6 banger. When in the mountains, I watch my temperature gauge pretty closely. I don't push it and keep my flashers on as soon as I drop below 50 or so. Usually I'm right in there with really loaded semis. So far I haven't had any issues but I don't break any land speed barriers either. Fortunately, most of these types of grades are pretty short.
Phil
|
|
|
03-21-2009, 07:15 PM
|
#4
|
Guest
|
I would check the highlander manual, most of the time it is recommended to turn off the OD when towing. Usually a switch or button ( on auto trans) . This makes for better trans cooling and less strain on the trans. It will hurt your mileage but save your transmission. Once back on fairly level ground, you can turn OD back on.
|
|
|
03-21-2009, 08:17 PM
|
#5
|
Guest
|
Quote:
Originally Posted by roned2
My question is this: Do I choose a gear when in the mountains or do I downshift when necessary. Is there a gear I should try to stay in. Thanks in advance for any replies.
|
I don't usually select a lower gear going up a grade but do downshift when the rpms get low. I try to keep the Tundra around 3000 rpm or better when pulling up a grade.
I do select a lower gear when going downhill on a steep grade so that I get more engine braking.
Hope this helps.
|
|
|
03-22-2009, 12:40 PM
|
#6
|
Guest
|
I just keep an eye on my trenamission temperature gauge. Unfortunately, not all tow vehicles have that.
What would it take to add a transmission temperature gauge?
For some vehicles, you could perhaps plug into the OBD II plug.
|
|
|
03-22-2009, 04:22 PM
|
#7
|
Guest
|
Scan Gauge
Take a lok at the SCAN GAUGE this is a wonderful device for towing,, It is about 2x5x2 and has a cord that plugs into the ODBII ( diagnostic port usually under the dash on the drivers side. It will report a host of information on the condition of the engine and transmission as well as mileage info. It is a great tool, relatively inexpensive and simple to install just stick on velcro , plug it in and your done.
|
|
|
03-28-2009, 09:46 AM
|
#8
|
Site Team
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,199
|
The SCAN GAUGE is a great choice. Another is the Aeroforce gauge ( www.aeroforcetech.com). If you have any concerns about your vehicle, one of these could save you a big repair bill.
Bill
|
|
|
03-28-2009, 09:49 PM
|
#9
|
TrailManor Master
Join Date: Nov 2008
Location: Chicago, IL
Posts: 1,063
|
Quote:
Originally Posted by rumbleweed
Take a lok at the SCAN GAUGE this is a wonderful device for towing,, It is about 2x5x2 and has a cord that plugs into the ODBII ( diagnostic port usually under the dash on the drivers side. It will report a host of information on the condition of the engine and transmission as well as mileage info. It is a great tool, relatively inexpensive and simple to install just stick on velcro , plug it in and your done.
|
Would you happen to know if it will give information like Transmission Fluid Temp on, say, a Toyota Sienna? I went to the website, but didn't see if that information was there, and it seems to be one of the important ones, according to some on this board.
If anything, it almost sounds like that information is not available, which then makes me wonder what this could be used for?
Marc
|
|
|
03-29-2009, 12:24 AM
|
#10
|
TrailManor Master
Join Date: Dec 2008
Location: Ventura County, CA
Posts: 273
|
I also have a Sienna and have looked at the ScanGauge. It looks like it provides useful info as part of the standard gauge but, from what I can tell, it looks like to get transmission temp you need to use the XGauge functionality (a way of adding additional codes your vehicle supports).
See below for a link to the current X-Codes: (Sadly, the only Toyota vehicle listed in the extended codes is a Prius)
http://www.scangauge.com/support/pdfs/XGAUGE.pdf
__________________
Former:
2009 2619 w/swing tongue
TV 2010 Tacoma Dbl Cab PreRunner
Prodigy Brake Controller/TST TPMS
15" Maxxis M8008 225/75R15
Honda EU2000i (Tri-Fuel Converted)
160W Solar/Morningstar Sunsaver MPPT
Xantrex Link-Lite & ProWatt SW2000 Inverter
Current:
2016 KZ Vision 23BHS
2015 Ford F150 SuperCrew 3.5 EcoBoost
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|